Electrical controllers
Tsubaki's electrical controller products are capable of monitoring, detecting abnormalities and controlling in machinery and equipment.
Current-monitoring type Shock Relay that quickly detects overcurrent in the event of motor overload and prevents equipment damage.
Power-monitoring type Shock Monitor that detects the input power of a motor, thereby capturing minute load changes and enabling feedback control of the device.
Both products electrically support 'visualisation' and equipment management at the manufacturing site.
What's New / Product Information
Rapidly advancing IoT is raising productivity and quality in factories.
Tsubaki plays a key role here, with electrical control devices that watch over factories by providing visualization of operational circumstances and detection of overload.
Shock Relay
These current-monitoring control devices quickly detect overcurrent during motor overload and thus prevent equipment from damage.
It can be used in a variety of applications, including lifting devices and conveyors.
Features
- ・Quick overcurrent detection
- ・Easy to install onto existing equipment
- ・Sends emergency signal only when problems detected
ED Series
SB Series
150 Series
Shock Monitor
These electricity-monitoring control devices detect minimal load variations by monitoring motor input power.
They can be used on machine tools to shorten processing times and detect broken drills.
Features
- ・Power detection to monitor minimal variations in load
- ・Wide frequency range (5 to 120 Hz)
- ・Quick response
- ・Records load conditions
Basic model
Economical type (H1)
Contact detection type (M1)
Electrical controllers Product list
Electrical Overload Protectors (Shock Monitor )
Shock Monitor TSM4000 Series
Model No. TSM4000~
Upgraded Shock Monitor capable of quick detection of minute load fluctuations
- ・The terminal block has a safe design with a cover.
- ・Equipped with analog output 0-10V as standard
- ・With the backlight auto-off function, helps you with energy-saving operations.
- ・Standardized panel-mounted type. Easy terminal wiring at the time of panel installation.
- ・Remote monitoring is possible by combining a touch-screen display and the Shock Monitor.
Type
Basic model
Shock Monitor TSM4000H1 Series
Model No. TSM4000H1~
For general industry machines. Economical Type.
- ・Fewer functions compared to the basic type make this type economical and easy to set.
- ・The relay output has two outputs and can be used as an alarm output (High 1) and an abnormal output (High 2).
- ・As a set, High 1 and High 2 can be switched from the external for a maximum of 4 types.
It is useful to change settings depending on the workpiece used for conveyor transportation. - ・It comes with an efficient torque monitoring function (20-120Hz) when using the inverter.
Type
Economical type
Shock Monitor TSM4000H2 Series
Model No. TSM4000H2~
For general industry machines. Load-following type
- ・Type in which the load setting value automatically changes and follows according to the fluctuating load.
- ・The writing cycle can be changed depending on the fluctuations of the efficiency change.
- ・Absolute value monitoring can be done by High 2, in which the operational levels do not change.
Type
Load following type
Shock Monitor TSM4000M1 Series
Model No. TSM4000M1~
For machine tools. Contact detection type
- ・Load ratio at no-load operation can be automatically, or by external input, offset to 0%. Quickly and reliably detects minimal load changes. (There are two types of output: OUT1 and OUT2)
- ・OUT3 is a non-offset value and the absolute value can be monitored.
- ・Detection level can be switched from the external for a maximum of 8 types. Compatible with the change of grinding stone and workpieces.
Type
Contact detection type
Shock Monitor TSM4000M2 Series
Model No. TSM4000M2~
For machine tools. Integral power type
- ・Detects overload and tool wear by integrating one cycle of power from the manufacturing process.
- ・The wear is detected by the upper limit (OUT2), and the drill breakage can be detected by the lower limit (OUT1).
- ・With the instantaneous value of OUT3, overload due to jams is monitored with the absolute value.
- ・Detection level can be switched from the external for a maximum of 8 types. Compatible with the change of grinding stone and workpieces.
- ・The integral time setting can be changed easily.
Type
Integrated power type
Shock Monitor TSM4000M3 Series
Model No. TSM4000M3~
For continuous processing tool Processing tool breakage detection type
- ・Power sensor for machining machines that instantly detects tool breakage.
Detects breakage of machining tool in 0.05 seconds - ・Double safety function of counter and wear detection
The counter function manages the life of parts, and wear detection catches tool wear. - ・Built-in PLCs enable remote catching of tool breakage and support for IoT.
Type
Processing tool breakage detection type
Shock Monitor TSM4000C1 Series
Model No. TSM4000C1~
For crushers. Built-in forward/reverse sequencer type
- ・Just by inputting starting signal, stopping, reverse movement and restarting during overload can be controlled without an external sequence program.
- ・In case the machine does not return to normal operation even after the preset reverse setting time has passed, the stopping signal is output to stop the device completely.
- ・The overload level, stop time, and reverse running time can be set easily on site.
- ・For energy saving, automatic stoppage available under no load.
Type
Built-in forward/reverse sequencer type